耐*陽極氧化鋁絲印移印水性油墨

耐*陽極氧化鋁絲印油墨銷售廠家！

1、適用范圍：產品主要用于金屬、電鍍、氧化鋁、電解板、鋁塑板、噴（烤）漆、噴塑等制品的絲印及移印。

2、產品特性：亮光、免烘烤、耐*、耐手汗、耐水泡、耐沖壓。

3、稀釋劑：用公司B-03專用稀釋劑或783稀釋油墨，用718洗網水清洗網版。

4、固化劑：?jiǎn)谓M份使用，不需要添加固化劑；如有特殊要求可選擇添加本公司JS-9固化劑用于增加油墨附著力及性能，添加量為10%-15%。

5、油墨調配：開罐使用前應充份攪拌，然后取所需量油墨加入稀釋劑稀釋至合適的印刷粘度進行印刷。

6、網版及刮膠：適合80T-140T（200目-350目）聚脂網紗，聚氨脂PU油性刮膠。

7、干燥條件及時間：

干燥溫度

25℃

60℃

80℃

100℃

干燥時間

24小時

40分鐘

30分鐘

20分鐘

產品烘烤溫度不可超過100℃。

【性能檢測】

1、3M膠帶劃百格測試：100%無脫落

2、耐沖壓測試：1mm厚鋁板180°折彎無變化。

3、耐*測試：用脫脂棉沾濃度99%工業*以500G力水平來回50次無脫色。

4、耐手汗耐試：用大拇指緊壓印刷面5分鐘后，再用力來回磨擦100次無脫色。

5、耐水性測試：用常溫自來水浸泡24小時，3M膠帶劃百格測試，100%無脫落。

【注意事項】

1、先小量試印確認符合要求后再批量生產。

2、做好承印物的表面清除油脂及雜質工作，以促進附著效果。

3、附著力、硬度、耐酸性、耐*性、耐化學品性、抗劃傷性、耐磨性等性能的檢測，

需要完全固化后方可檢測。

4、未經允許情況下，不得將系列油墨與其它類型油墨混用及配色。

5、油墨，稀釋劑使用及儲存時嚴禁煙火。

 The products are mainly used in screen printing and the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface and various ceiling oxide board, mirror panels, coated board, roller coated board and other products.

2, product characteristics: light, good adhesion, fast drying, stamping resistance.

3, diluent: with our B-03 special thinner or 783 open oil, washing network water cleaning screen with 718.

4, curing agent: one component use, can also choose to add our JS-10 special curing agent is used to increase the ink adhesion and physical and chemical resistance.

5, printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. If you need to add curing agent, first add curing agent after mixing and set aside for 10 minutes, and curing agent for ink completely crosslinking after dilution.

6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.

7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink Unrecyclable.

[detection] performance

1, 3M tape row adhesion test: 100% without shedding

2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.

3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500G stress level and back 200 times without decolorization.

[note]

1, the first small try printing again after confirmation of compliance with the requirements of mass production.

2, do a good job in the substrate surface to remove grease and impurities, in order to promote the adhesion effect.

Detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, abrasion resistance and other properties,

Fully cured before detection.

4, without permission, may not use the series of ink and other types of ink mixing and matching.

5, ink, fireworks is strictly prohibited the use of thinner and storage.

6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.

7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing or direct help doctor.